Dehumidification
Showing 10–15 of 15 results
-
Condenser dryer DH-300 BY
The condenser dryer DH-300 BY is the largest condenser dryer available for rental in the Netherlands... Featured specs Air volume 5,000 m³/h Maximum capacity 600 l / 24 h -
Adsorption dryer TTR-2800
The adsorption dryer TTR-2800 is equipped with technology according to the highest industrial requirements. This dryer is... Featured specs Amount of dry air (nominal) 2,800 m³/h at 300 Pa. Reactivation air volume 570 m³/h at 300 Pa -
Adsorption dryer MDC-1000
The MDC-1000 adsorption dryer is designed for general purposes such as... Featured specs Amount of dry air (nominal) 1,000 m³/h, at 200 Pa. Reactivation air volume 400 m³/h, at 280 Pa -
Adsorption dryer MDC-2000
The MDC-2000 adsorption dryer is designed for: building drying, room air dehumidification, dry air storage... Featured specs Amount of dry air (nominal) 2,000 m³/h, at 200 Pa. Reactivation air volume 400 m³/h, at 280 Pa -
Adsorption dryer MDC-3000
The MDC-3000 adsorption dryer is designed for: building drying... Featured specs Amount of dry air (nominal) 3,000 m³/h, at 200 Pa. Reactivation air volume 770 m³/h, at 270 Pa -
Adsorption dryer MDC-5000
The MDC-5000 adsorption dryer is designed for: building drying... Featured specs Dry air volume (nominal) 5,000 m³/h at 260 Pa Regeneration air 1,600m³/h at 280 Pa
Application options for our construction dryers and dehumidifiers:
- Building drying for faster drying of new buildings, extensions and renovations
- Drying after water damage, flooding and calamities
- Flooding after floods
- Air dehumidification during temporary storage or drying processes
Application options for our industrial dehumidifiers:
- Production and storage areas (also installations with specific humidity requirements)
- Industrial process and product drying, room dehumidification
- Corrosion protection for tanks, ships and moisture-sensitive cargoes
- Dehumidification in water technical installations and for the prevention of condensation
- Preventing corrosion in switchgear, boiler installations, turbines and pipelines
- Prevention of condensation in loading/unloading areas, cold stores at temperatures below -15 °C
For an accurate calculation of the dehumidification capacity, especially for larger rooms or complicated climatic environmental conditions, please contact one of our consultants. We analyze on location, the individual needs and determine the required capacity. Based on this, we work out a customized solution for you.​
Below you will find more information about the operation of the condensation dryers and the adsorption dryers:
Condensation dryers
With condenser dryers, the sucked in and moist air is strongly cooled by means of a condenser. the evaporator section of a closed refrigeration system.
Due to this cooling, the relative humidity of the air rises above 100%, causing the water vapor to condense. The condensed water is drained to a reservoir or is led outside through hoses. The heat released in the condenser of the refrigeration system is used to cool the air above the original temperature.
Adsorption dryers
Desiccant dryers make use of the moisture-absorbing capacity of substances such as silica gel and lithium chloride. These substances are impregnated on a rotating ceramic wheel, which blows the moist air out of the room.
The hygroscopic material absorbs a large part of the moisture and the air then leaves, dry the adsorption dryer. Depending on the model, this process takes place over two separate steps air ducts (Dual) or via a common air stream (Mono), of which a partial air stream is then used for regeneration.
Separated air flows offer the advantage of pressure-neutral convection drying with higher drying results and significantly more energy efficiency when installed indoors and outdoors.
